Feature Summary
  • Configuration Reset
  • IEEE 802.11b: 6 Bridge links, 64-bit and 128-bit WEP, Replaceable antennas
  • DHCP client
  • Firmware Upgrade: Xmodem-based, TFTP-based, HTTP-based
  • Management: Web-based UI, UPnP, SNMP MIB1, MIB2, Enterprise MIB
  • Antenna alignment Assistance, Link Health Monitoring
  • Power over Ethernet (Optional)
  • Hardware Watchdog Timer

IWE 1100B+ 
Wireless_LAN-to-LAN Bridge
 
OvisLink's IWE1100B+ IEEE 802.11b-based wireless LAN-to-LAN Bridge offer versatile and cost-effective a low-cost way to joint LAN segments that may be far separate (e.g., in different buildings) to a complete network.

It can be configured either as an AP (Access Point) interface or a LAN-to-LAN bridge interface. Therefore, it flexibly provides Access Point and Bridge function simultaneously to fit vary wireless applications. The high-performance radio allows. Moreover, it can optional support 22Mbps data rate for double speed of wireless backbone connections !

The default antennas can be replaced with high-gain directional/omni-directional antennas for different purposes. It also provides the Antenna Alignment Assistance in Wi-Link Network Manager Suite that can allow the antenna aligning can be easily adjusted without using the eyes !

The optional POE function allows the power feeding by Ethernet cable to eliminate the additional power line requirement in special install environment. With the sleek and intuitive Web-based user interface, the IWE1100B+ can be easily managed and satisfied by system integrators’ various requirements.
Usage Scenarios
LAN-to-LAN
The bridge can be used to join two LAN segments in two buildings into a complete network. By using high-gain antennas, the distance between two buildings can be miles long.

Co-existing AP and Bridge Function
The bridge can also be used in a "star" like application to join up to 6 network segments.

Wireless AP Client
Can associated with any 3rd party AP, there’re 2 applications ---

  • Bridge to single Ethernet Device
  • Bridge to Ethernet LAN for multiple devices.
Specifications
Standards IEEE 802.11b HR for wireless LAN
IEEE 802.3u 10/100BaseTX for Ethernet LAN   
Spreading DSSS (Direct Sequence Spread Spectrum)
Security 64-bit and 128-bit WEP Encryption
Frequency range           2.400~2.4835 GHz (subject to local regulations)
Operating range  Open Space: 100-300m Indoor: 35m-100m
Supported bit rate  11Mbps, 5.5Mbps, 2Mbps, 1Mbps
High performance Automatic Scale Back Functionality, long (short) preamble
Data rate and modulation CCK @ 11/5.5 Mbps DQSK @ 2 Mbps DBPSK @ 1 Mbps
Operating channels USA (FCC): 1-11 Canada (IC): 1-11
Europe (ETSI): 1-13 France: 10-13
Japan: 1-13 (TELEK) / 1-14 (MKK) 
Transmit (output) power  18dBm typical
Receiver sensitivity Better than -80dBm
Port characteristics LAN port (100Base-TX): RJ45 * 1   COM port: RS232 * 1      
Antenna system One antenna diversity system 2dB gain
Utilities Web-based Network Manager
Network protocols TCP/IP, NetBIOS, IPX/SPX, NetBEUI, AppleTalk

Physical and Environmental
LED indicators Power, LAN Link/ACT, RF Link/ACT, System Alive  
Power adapter  Input: AC 100~120V 47~63 Hz, 1.0A
MAX Output: DC 5V, 2.5A 
Dimensions 175 x 145 x 50 mm
Temperature range 0~55oC (Operating), -20~70oC (Storing)
Humidity Max. 5%~95% Non-condensing in storage
Certification FCC part 15 class B in US, ETSI 300.328 and CE EMC-EEC in Europe 
Warranty 1 year

Ordering Information Vendor’s Disclaimer Statement
The information in this document is subject to change without notice and does not represent a commitment on the part of the vendor. The vendor reserves the right to make changes to the content of this document and/or the products associated with it at any time without obligation to notify any person or organization of such changes.